Search Results

Correlations for the ignition delay and combustion energy release intervals in a homogeneous charge, spark-ignited engine are developed. After incorporation within a simplified engine cycle simulation, predicted values of these two combustion parameters are compared to experimental engine data. The correlations are based on four fundamental quantities-the turbulent integral scale, the turbulent micro-scale, the turbulent intensity, and the laminar flame speed. The major assumptions include: (1) The turbulent integral scale is proportional to the instantaneous chamber height prior to flame initiation. (2) Angular momentum is conserved in the individual turbulent eddies ahead of the flame front (i.e., a “rapid distortion” turbulence model). (3) The turbulent intensity scales with the mean piston speed. Two empirical constants scale the correlations to a given engine.

Since the advent of the spark ignition engine, the maximum engine efficiency has been knock limited. Knock is a phenomena caused by the rapid autoignition of fuel/air mixture (endgas) ahead of the flame front. The propensity of a fuel to autoignite corresponds to its autoignition chemistry at the local endgas temperature and pressure. Since a fuel blend consists of many components, its autoignition chemistry is very complex. The octane index (OI) simplifies this complex autoignition chemistry by comparing a fuel to a Primary Reference Fuel (PRF), a binary blend of iso-octane and n-heptane. As more iso-octane is added into the blend, the PRF is less likely to autoignite. The OI of a fuel is defined as the volumetric percentage of iso-octane in the PRF blend that exhibits similar knocking characteristics at the same engine conditions.

Among the recent research ideas to reduce hydrocarbon emissions emitted from SI engines till light-off of catalyst since cold start are those exploiting non-thermal plasma technique and photo-catalyst that draws recent attention by virtue of its successful application to practical use to clean up the atmosphere using the feature of its relative independence on temperature. Based on the previous research results [6] obtained with model exhaust gases using an experimental emissions reduction system that utilizes the non-thermal plasma and photo-catalyst technique, further investigation was conducted on a production N/A 1.5 liter DOHC gasoline engine during cold start to warm-up. For the effects of non-thermal plasma-photocatalyst combined reactor, 10% concentration reduction was achieved with the fuel component paraffins, and the large increase in non-fuel paraffinic components and acetylene concentrations were similar to those of base condition.

Measurements were made of exhaust histories of the following species: unburned hydrocarbons (HC), carbon monoxide, carbon dioxide, oxygen, and nitric oxide (NO). The measurements show that the exhaust flow can be divided into two distinct phases: a leading gas low in HC and high in NO followed by a trailing gas high in HC and low in NO. Calculations of time resolved equivalence ratio throughout the exhaust process show no evidence of a stratified combustion. The exhaust mass flow rate is time resolved by forcing the flow to be locally quasi-steady at an orifice placed in the exhaust pipe. The results with the quasi-steady assumption are shown to be consistent with the measurements. Predictions are made of time resolved mass flow rate which compare favorably to the experimental data base. The composition and flow histories provide sufficient information to calculate the time resolved flow rates of the individual species measured.

In the jet-ignition prechamber stratified-charge spark-ignition engine, the fuel-air mixture at the time of combustion is non-uniform. Instantaneous exhaust mass flow rates and emission concentrations from this engine were measured and used to determine the degree to which this charge stratification persists in the products of combustion immediately downstream of the exhaust valve throughout the exhaust process. In all the cases studied no appreciable variations, during the exhaust process, were detected either in the air-fuel ratio of the exhaust gases as a function of time or in the instantaneous concentrations of CO2, O2 and NOx. The experimentally obtained instantaneous HC and CO concentrations in the exhaust, however, displayed large fluctuations and were used to study the sources of these two pollutants in this engine.

A prior study (Chon and Heywood, [1]) examined how the design and performance of spark-ignition engines evolved in the United States during the 1980s and 1990s. This paper carries out a similar analysis of trends in basic engine design and performance characteristics over the past decade. Available databases on engine specifications in the U.S., Europe, and Japan were used as the sources of information. Parameters analyzed were maximum torque, power, and speed; number of cylinders and engine configuration, cylinder displacement, bore, stroke, compression ratio; valvetrain configuration, number of valves and their control; port or direct fuel injection; naturally-aspirated or turbocharged engine concepts; spark-ignition and diesel engines. Design features are correlated with these engine’s performance parameters, normalized by engine and cylinder displacement.